Nov.2026 20
Views: 78
Military UAV Power: UAS Classes, Flight and Payload Buses, Launch and Recovery Loads, and the Honest Sealed NiMH Role
Introduction
Paper A: how military unmanned aircraft consume power. DoD Groups 1-5, flight versus payload buses, hover and cruise energy, launch and recovery peaks, ground-support loads and temperature/altitude effects. Lithium owns the flight pack; sealed NiMH fits ground carts, test benches, launch controllers and training airframes.
Details

Military UAV power — UAS classes, flight and payload buses, launch and recovery loads, and the NiMH support role

A military unmanned aircraft is a power system with wings, a datalink and a mission computer attached. The flight battery is sized by hover or cruise power, the payload bus is sized by sensors and processors, the launch and recovery equipment is sized by short mechanical overloads, and the ground support equipment is sized by how many sorties the unit intends to fly before the generator runs. These four budgets meet in one airframe but obey different rules. This paper separates them, gives the arithmetic that connects takeoff weight to electrical power, and states precisely where a sealed nickel-metal-hydride (NiMH) pack is a defensible choice — and where it is not.

Key facts at a glance

  • The DoD classification is a weight, altitude and speed chart, not a battery specification. Group 1 is 0–20 lb, Group 2 is 21–55 lb, Group 3 is under 1,320 lb, and Groups 4 and 5 are above 1,320 lb with different altitude envelopes. Electrical architecture varies far more within a group than between groups.
  • Flight energy is dominated by one number: power divided by endurance. A 274 Wh pack that flies a 9 kg multirotor for 55 minutes is delivering roughly 600 W average if the aircraft carries two packs. The same pack on a 1 kg aircraft would last far longer because the aircraft needs far less power.
  • Payload power is a separate bus. Sensor gimbals, radar, SIGINT payloads, mission computers and datalinks often run from a 12–28 V payload rail that is independent of the 6S–14S flight rail. That separation is what makes a support chemistry possible at all.
  • Launch and recovery are peak-power events, not energy events. A catapult, a parachute opening, a recovery net or a vertical takeoff concentrates power into seconds; sizing them from average mission power is a common error.
  • NiMH belongs to the ground and training layer. Ground support carts, battery test benches, launch controllers, recovery winch controls, training airframes, maintenance sets and handheld ground stations — not the flight main pack of a performance UAV.

The five UAS groups and what they imply for power

The U.S. Department of Defense categorizes unmanned aircraft by maximum gross takeoff weight, normal operating altitude and speed. The chart below reproduces the published group boundaries and adds the electrical architecture that typically accompanies each class. The examples are representative, not exhaustive.

Group Max gross takeoff weight Normal altitude Speed Representative aircraft Typical electrical architecture
1 0–20 lb (0–9.1 kg) Below 1,200 ft AGL Up to 100 kt RQ-11 Raven, RQ-14 Dragon Eye, Wasp, Puma Single 3S–6S LiPo or Li-ion pack, 11.1–22.2 V; payload on a regulated 5/12 V rail
2 21–55 lb (9.5–25 kg) Below 3,500 ft AGL Below 250 kt ScanEagle, RQ-21 Blackjack, Silver Fox, Aerosonde 6S–12S Li-ion or LiPo, sometimes dual-pack; separate avionics and payload rails
3 Under 1,320 lb (600 kg) Below 18,000 ft MSL Below 250 kt RQ-7B Shadow, RQ-15 Neptune, XPV-1 Tern 12S–14S Li-ion or LiPo flight packs; 28 V avionics bus; generator on some airframes
4 Above 1,320 lb Any, usually below 18,000 ft Any MQ-1C Gray Eagle, MQ-8B Fire Scout, MQ-5B Hunter Turbine or heavy-fuel engine with generator; battery for start, emergency and avionics ride-through
5 Above 1,320 lb Above 18,000 ft MSL Any MQ-9 Reaper, RQ-4 Global Hawk, RQ-4N Triton Engine-driven generator; 28 V DC and 115/230 V AC buses; battery is an emergency source

The lesson for a battery supplier is that "military UAV" is not one requirement. A Group 1 airframe is an energy-limited consumer device; a Group 3 airframe is a small aircraft with an avionics bus; a Group 5 airframe is a generator-powered platform whose battery exists for start, emergency and ride-through. A pack specification that does not name the group and the bus it serves is not a specification.

Flight rail, payload rail and ground rail

Most professional multirotors and small fixed-wings have at least three electrical domains. They are often confused in RFQs because all three are measured in volts and watts, but they have different load profiles and different safety consequences.

Domain Typical voltage Load character What it powers Consequence of failure
Flight rail 22.2 V (6S), 44.4 V (12S), 51.8 V (14S) High continuous current, large transient on climb Motors and ESCs Loss of thrust; immediate forced landing or crash
Avionics rail 5 V, 12 V, 28 V regulated Steady, low current, sensitive to noise Flight controller, IMU, GNSS, datalink Loss of control or navigation; failsafe behaviour depends on design
Payload rail 12 V, 24 V, 28 V, sometimes 48 V Mission-dependent, often the largest average load after motors EO/IR gimbal, radar, communications payload, sprayer, cargo release Loss of mission; may be recoverable
Ground rail 12 V, 24 V, 28 V, 48 V Intermittent, high peak during charging or launch GSE, chargers, launch and recovery equipment, ground station Sortie delay; no airborne consequence

This separation matters because it defines where a support chemistry can live. A NiMH pack cannot compete on the flight rail of a performance aircraft, but it can run the ground rail, the training rail and some payload checkout rails without touching flight safety. The boundary should be written into the requirement, not left to the pack supplier to infer.

From takeoff weight to average electrical power

Multirotor hover power scales roughly with mass to the 1.5 power, because disk loading and induced power both rise as the aircraft gets heavier. Published flight times and pack energies give a practical cross-check: average power is pack energy divided by endurance, with a reserve for go-around and wind.

Pavg ≈ Eusable / tendurance      Ppeak ≈ 1.5–2.0 × Pavg for multirotors

Aircraft class Energy carried Published endurance Implied average power Planning note
1 kg quadcopter, 77 Wh pack 77 Wh 46 min ≈ 100 W Consumer-class airframe; hover is the design point
9 kg multirotor, 2 × 274 Wh 548 Wh 55 min ≈ 598 W Dual-pack professional airframe; payload reduces endurance
10 kg hexacopter, 2 × 274 Wh 548 Wh 40 min ≈ 822 W Higher disk loading and payload; planning figure
Group 2 fixed-wing, 6S 4 Ah Li-ion ≈ 355 Wh 2 h ≈ 178 W Cruise-dominated; launch transient is separate
Group 3 fixed-wing, 14S 20 Ah Li-ion ≈ 1,036 Wh 5 h ≈ 207 W cruise Illustrative; actual cruise power depends on mass and speed

These numbers are a sanity check, not a design tool. The important point is the order of magnitude: a small multirotor averages hundreds of watts, a Group 3 fixed-wing averages hundreds of watts in cruise but kilowatts in climb, and a Group 4/5 aircraft averages kilowatts to tens of kilowatts and is not battery-powered in the usual sense. A NiMH pack offered against the flight rail of the first two classes will lose on mass; a NiMH pack offered against the ground rail of any class can win on cost, safety and logistics.

Launch and recovery: the peak-power events

Launch and recovery equipment is where average-power thinking fails. A catapult accelerates the aircraft in a fraction of a second; a parachute opening converts kinetic energy into a shock load; a recovery net stops the aircraft in a short distance. The electrical load may be modest, but the mechanical load and the current transient are not.

Method Typical acceleration or shock Duration Electrical consequence
Bungee or pneumatic catapult 5–10 g 0.1–0.3 s Launch controller and release actuator draw a short pulse; battery must hold voltage through the pulse
Hand launch 1–2 g < 0.1 s No ground electrical load; flight pack sees a current step
Parachute recovery 3–5 g opening shock 0.1–0.5 s Pyrotechnic or electromechanical release; one-shot actuator current
Net or catch recovery 5–8 g deceleration < 0.2 s Winch or net drive may regenerate; controller needs ride-through
Vertical takeoff and landing 1.5–2 × hover power Seconds Flight pack, not GSE; peak current sets connector and fuse rating

For a ground-support battery, the relevant question is not the average mission power but the largest short-duration current the pack must deliver while staying above the controller's brown-out threshold. A 24 V 10 Ah NiMH pack with a 20 A continuous rating can supply a 40 A pulse for a second or two if the connector and wiring are sized for it; the same pack may fail to start a compressor or a winch whose inrush is 60 A. The datasheet must state both continuous and pulse ratings, with the pulse duration.

Ground support equipment: the load nobody budgets

Ground support is a real electrical load, and on a small unit it can exceed the aircraft's average flight power. Battery stations, chargers, generators, launch compressors, recovery winches, ground control stations and maintenance laptops all draw from the same field power system.

GSE item Typical power Duty Why it matters
Dual-channel intelligent battery station 750–1,070 W input 30–60 min per pair of flight packs Dominates the field generator load during turnaround
Field generator 2–5 kW Continuous during operations Sets fuel consumption and acoustic signature
Launch compressor or accumulator pump 0.5–2 kW Minutes per launch High inrush; may share the GSE battery bus
Recovery winch 0.5–3 kW Minutes per recovery Peak load and regeneration; controller needs a stable bus
Ground control station 100–500 W Continuous Displays, datalink and recording; often the baseline hotel load
Battery test bench 50–300 W Per test session The classic NiMH support load

Published battery-station data make the point concrete. The DJI BS60 accepts 100–120 V AC or 220–240 V AC, draws up to 1,070 W, delivers 750 W at 110 V and 992 W at 220 V, stores eight TB60 flight packs and four WB37 packs, and charges two TB60 packs plus one WB37 simultaneously. A 220 V supply fills two TB60 packs in about 60 minutes. That is a 1 kW-class load for an hour, before the generator, lights and ground station are counted.

This is the gap a sealed NiMH support pack can fill: it can carry the ground station, the test bench and the launch controller through a generator-off period, or buffer the generator during a high-inrush launch, without adding a lithium pack to the logistics chain. The pack is not flying, so its energy density penalty is tolerable, and its transport classification is simpler than a lithium flight pack.

Temperature, altitude and the real operating envelope

Condition Flight pack expectation Ground support pack expectation Design consequence
−20 °C soak Capacity derated, heater or preheat required May be stored and used cold; capacity derated Specify usable capacity at the lowest expected temperature, not at 25 °C
+50 °C ambient Charge and discharge derated; thermal management Often shaded or in a vehicle; still hot Separate storage, charge and discharge limits
18,000 ft equivalent Low pressure affects connectors, cooling and some cells Usually not exposed; air cargo hold is pressurized Do not apply an altitude rating the GSE never sees
Salt fog and sand Airframe-level protection Field cart and test set need IP rating and sealed connectors Ingress protection is a pack-level requirement
Vibration and shock Flight-qualified mounts and cells Vehicle transport and handling drops MIL-STD-810H vibration and shock are still relevant

A common over-specification is to apply the aircraft's altitude and vibration requirements to a ground cart that never leaves the truck. The opposite error is to apply a commercial IP54 rating to a pack that will be stored on a wet flight line. The correct envelope is the one the pack actually sees, written down and tested.

Where a sealed NiMH pack is defensible

Application Why NiMH fits What to specify
Ground support cart Moderate energy, high cycle count, simple charging, non-flight safety case 24 V 10–20 Ah, 20 A continuous, 40 A pulse, IP54, UN 3496
Battery test bench Instrument load, intermittent, benchtop charging 12 V 7–15 Ah, low ripple, thermistor, fused output
Launch controller Short pulses, redundancy, wide temperature 12–24 V, 10–30 A pulse, low-temperature capacity
Recovery winch control Stable bus during regeneration and shock 24 V, 20 A continuous, reverse-polarity and overcurrent protection
Training airframe Repeated charge/discharge, abuse tolerance, low cost per cycle 6S–12S equivalent, 5–10 Ah, 1C charge, 2C discharge
Handheld ground station Long standby, small display, occasional transmit 12 V 3–7 Ah, low self-discharge, −20 °C operation
Payload checkout set Bench power for gimbal, radar or datalink before flight 24–28 V, clean output, current limit, e-stop
UAV ground-support load audit

What is not defensible

  • No NiMH flight main pack for a performance multirotor. At 70–100 Wh/kg pack level, a NiMH pack that replaces a 274 Wh LiPo would add roughly 1.4–2.5 kg for the same energy, which a 9 kg aircraft cannot spare.
  • No NiMH pack for a long-endurance fixed-wing. Cruise energy over several hours rewards gravimetric energy density; lithium owns that mission.
  • No claim that NiMH "powers military UAVs". The correct claim is narrower: sealed NiMH powers the ground, test, launch, recovery and training layer around UAV operations.
  • No NiMH pack on a 28 V avionics bus without a documented voltage window. Avionics tolerate a defined input range; a sagging NiMH pack under pulse load may drop below it.
  • No substitution for a certified flight battery. Airworthiness, ASTM F3005, DO-311A and the aircraft manufacturer's approval are not transferable to a different chemistry or pack design.

Case data: what the published numbers say

Item Published value What it tells a pack designer
DJI TB60 flight pack 5,935 mAh, 52.8 V, 12S LiPo, 274 Wh, 1.35 kg, −20 to +50 °C Pack-level 203 Wh/kg; a NiMH equivalent of the same energy would be 2.7–3.9 kg
DJI TB65 flight pack 5,880 mAh, 44.76 V, Li-ion, 263.2 Wh, 1.35 kg Same mass, slightly lower energy; chemistry choice is airframe-specific
DJI BS60 battery station 1,070 W max input, 992 W output at 220 V, 8 × TB60 storage, 2 + 1 simultaneous charge Turnaround power is a kilowatt-class GSE load, not a small accessory
ASTM F3005-22 Defines sUAS battery cells, mechanical design, electrical design and maintenance records; subordinate to F2910 A design checklist for flight packs; not a substitute for airworthiness approval
DoD UAS chart Group 1 0–20 lb; Group 2 21–55 lb; Group 3 < 1,320 lb; Groups 4–5 > 1,320 lb Defines the class, not the bus; ask for the bus and duty cycle

The TB60 number is the cleanest illustration of why chemistry matters. Its pack-level specific energy is about 203 Wh/kg. A well-built sealed NiMH pack at 80 Wh/kg would need 3.4 kg for 274 Wh, and at 100 Wh/kg it would need 2.7 kg. On a 9 kg aircraft with two packs, that is an extra 2.7–4.1 kg of mass — enough to change the aircraft's endurance, centre of gravity and certification basis. No honest supplier should propose it for the flight rail.

What to ask a UAV OEM before quoting a support pack

Question Why the answer changes the pack Typical answer to expect
Which UAS group and which electrical bus does the pack serve? Sets voltage, energy and safety criticality Group 1–3; 24 V ground bus or 12 V payload checkout
Is the pack flown, carried, or ground-only? Determines whether airworthiness and flight standards apply Ground-only for GSE; flown only for training airframes
What is the continuous and pulse current? Sets cell count, tab design, connector and fuse 10–20 A continuous, 30–60 A pulse for launch/recovery
What is the lowest and highest operating temperature? Sets usable capacity, charge limits and heater need −20 to +55 °C for field GSE; 0–40 °C for bench
How is the pack charged and stored? Sets charger, balancing and state-of-charge policy Opportunity charging from a generator or vehicle; 30–50 % SOC storage
What ingress and shock does it see? Sets IP rating, enclosure and mounting IP54–IP65; vehicle transport and handling drops
What transport documentation is required? Sets UN 3496 paperwork and packing Road and air cargo; nickel chemistry, not lithium

How this changes a UAV support-equipment specification

Write the requirement around the ground mission, not the aircraft's nameplate. A ground cart that supports six sorties between generator runs needs an energy budget of six turnaround loads, not the aircraft's flight energy. A launch controller needs a pulse rating and a brown-out threshold, not a capacity rating. A battery test bench needs measurement accuracy and a safe current limit, not energy density. A training airframe needs cycle life and abuse tolerance, not a 200 Wh/kg cell.

The next paper turns these principles into a sizing procedure: load audit, chemistry comparison, cell count, derating stack, charge termination and protection. The third paper covers the test and certification route, including the environmental, EMC and transport tests that a "military-grade" claim usually omits.

UAV power domains and load profile

Frequently asked questions

Does a military UAV use a NiMH flight battery?

Not for the flight main pack of a performance aircraft. Small and medium UAVs use lithium-polymer or lithium-ion packs because energy density and voltage bus mass matter. NiMH appears in ground support, test, launch, recovery and training equipment, and occasionally in legacy or low-performance airframes where the designer has chosen it for abuse tolerance or supply-chain reasons.

Why not replace a 274 Wh LiPo with a NiMH pack of the same energy?

Because the mass penalty is decisive. At 80–100 Wh/kg pack level, 274 Wh requires 2.7–3.4 kg, versus 1.35 kg for the TB60. On a 9 kg aircraft carrying two packs, that is an extra 2.7–4.1 kg, which reduces endurance, payload or both, and may invalidate the centre-of-gravity and structural assumptions.

What is the difference between a flight battery and a ground-support battery?

A flight battery is part of the airworthiness case: its failure can cause loss of the aircraft. A ground-support battery is not; its failure delays a sortie or interrupts a test. That difference allows a wider chemistry choice, a simpler BMS and a different transport and certification route.

Which standard covers small UAS batteries?

ASTM F3005-22 defines requirements for cells, mechanical design, electrical design and maintenance records for batteries used in small unmanned aircraft systems, subordinate to ASTM F2910. It is a design and documentation standard, not an airworthiness approval, and it does not by itself authorize a chemistry change.

Can a NiMH pack be used on a 28 V avionics bus?

Only if the avionics input range and the pack's worst-case voltage under pulse load are both documented and compatible. A 24-cell NiMH string has a nominal 28.8 V but drops under load and rises on charge; the avionics may accept 18–36 V, or may not. The interface control document should state the window, not just the nominal voltage.

Is a NiMH ground pack treated as dangerous goods for air transport?

Nickel-metal-hydride batteries are assigned UN 3496, not the lithium entries UN 3480 or UN 3481, and no UN 38.3 test summary is required. The applicable packing instruction and quantity limits depend on the configuration and mode; the shipper should confirm them for each shipment.

Sources

U.S. Federal Aviation Administration, Aeronautical Information Manual, Chapter 11 Section 3, DoD UAS Categorization Chart (Group 1 0–20 lb, Group 2 21–55 lb, Group 3 <1,320 lb, Groups 4–5 >1,320 lb); Congressional Research Service, Defense Primer: Categories of Uncrewed Aircraft Systems; DJI Matrice 300 RTK specifications (TB60 5,935 mAh, 52.8 V, 274 Wh, 1.35 kg; BS60 1,070 W input, 992 W output at 220 V); DJI Matrice 350 RTK specifications (TB65 5,880 mAh, 44.76 V, 263.2 Wh, 1.35 kg); ASTM F3005-22, Standard Specification for Batteries for Use in Small Unmanned Aircraft Systems (sUAS); ASTM F2910, Specification for Design and Construction of a Small Unmanned Aircraft System; RTCA DO-311A, Minimum Operational Performance Standards for Rechargeable Lithium Battery Systems; MIL-STD-810H, Environmental Engineering Considerations and Laboratory Tests; MIL-STD-461G, Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment. Values marked illustrative are planning figures, not measurements.

Next in this series

Paper B — Selecting and sizing sealed NiMH packs for UAV ground support: load audit, chemistry comparison, cell configuration, derating stack, charge termination and protection. Paper C — Testing and certifying those packs: IEC 61951-2, IEC 62133-1, IEC 60529, MIL-STD-810H, MIL-STD-461G and the UN 3496 route.

Weijiang Power — sealed NiMH cells and packs for industrial support equipment.
OEM and custom configurations, with honest chemistry boundaries. Visit our product range or browse the full technical series.

Lastest News
Unlock the power of lithium batteries for lasting performance in handheld vacuum cleaners. Weijiang Li-on Battery leads the charge in innovation.
READ MORE
A NiMH battery pack is a collection of individual NiMH batteries connected in series or parallel to create a higher voltage or capacity battery.
READ MORE
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Name*
Whatsapp/Phone
Email*
Message*
Professional battery factory, support OEM & ODM customization.
REQUEST MORE DETAILS
Please fill out the form below and click the button to request more information about
Company Name*
Email Address*
WhatsApp / Phone*
Message & Requirements*

Buyer fact sheet

Weijiang Power at a glance

Legal entityShenzhen Weijiang Battery Co., Ltd., trading as Weijiang Power
Founded2010, 16 years of NiMH battery manufacturing
FactoryHuizhou Shenzhou Super Power Technology Co., Ltd., Zhongkai High-tech Zone, Huizhou, Guangdong; 12,000 m2, 4 workshops
Capacity200,000 NiMH cells per day; 200+ staff including 11-20 R&D engineers and 10 QC inspectors
Product rangeNiMH cells A, AA, AAA, SC, C, D, 9V, F, Sub-C, 4/5AA, 2/3A; custom NiMH packs; chargers; button and alkaline cells
CertificationsCE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001:2015, ISO 14001, IATF 16949, IEC 62321, MSDS, UL, IEC 62133; 16 patents; UN38.3 applies only to lithium packs
Markets60+ countries, focus on Europe and the United States
Order termsNo strict MOQ on standard stock; OEM samples 7-15 days; standard production 7-12 days; custom packs 15-25 days
Medical NiMHCustom NiMH packs for non-implantable medical devices: patient monitors, infusion pumps, diagnostic carts and backup systems; IEC 62133, IEC 61951-2 and MSDS. Medical NiMH page

Quick answers for buyers

Who is Weijiang Power?
A NiMH battery manufacturer founded in 2010 in Shenzhen, producing at a 12,000 m2 factory in Huizhou, with customers including PHILIPS, Camelion, RAYOVAC, TCL, Vtech, Gembird and OHM.

What can Weijiang Power supply?
Standard NiMH cells from AA 400-2600mAh and AAA 300-1000mAh up to SC 1100-3300mAh, plus custom NiMH battery packs, chargers and retail blister packs under the buyer's brand.

Which certificates are available for EU and US buyers?
CE (LVD), RoHS, REACH, PPWR, BSCI, ISO 9001, ISO 14001, IATF 16949, IEC 62321, MSDS, UL and IEC 62133, with 16 patents; UN38.3 applies only to lithium packs.

What is the minimum order and lead time?
Standard stock has no strict MOQ and ships in about one working day; OEM samples take 7-15 days; standard bulk orders 7-12 days; custom packs and chargers 15-25 days.

How do I get a sample or a quote?
Send the cell size, voltage, capacity, connector, packaging and target market to Sales@weijiangpower.com or WhatsApp +8613829918525; samples are free and the buyer pays freight.

Deeper reading: NiMH battery sourcing guide for EU and US buyers · EU battery regulation and NiMH compliance guide · Certification checklist · Full FAQ

Language versions: Deutsch · Français · Español

Last reviewed: 20 November 2026. Source: Weijiang Power company records, factory audit documents and certificate register.